PROJECT

Sourcing collaborative robot arms for a project

Compare key selection criteria for collaborative robot arms, avoid sizing errors, and prepare a complete project quotation with Atlas.

Industrial project profiles suited to collaborative robot arms

Manufacturing teams deploy Collaborative Robot Arms across end-of-line palletizing, machine tending, heavy pick-and-place, and shared assembly cells. When scoping a cell, buyers weigh six-axis articulation against high-speed four-axis kinematics according to part orientation and floor footprint. A six-axis unit such as the Elite Robots CS530H handles 30 kg payloads across a 1522 mm reach for palletizing or heavy fixture loading around human operators.\n\nWhere vertical transfers dominate over an unobstructed horizontal plane, the CRP Robot CRP-RS12-60Z40 provides a 60 kg maximum load across a 1200 mm arm span. For medium-payload tending near cutting fluid or dust, the Inovance IR-R16-210 S-INT at 16 kg and the Inovance IR-R25-178 S-INT at 25 kg bring sealed wrist housings that accommodate multi-jaw grippers without pushing payload margins to their mechanical limit.

Operational risks of selecting an undersized or mismatched robot arm

Underestimating combined part, tool-changer, and gripper mass triggers joint torque faults and accelerates gearbox wear during deceleration. Insufficient vertical travel also blocks part extraction above tall machine vises, while light pedestals flex under rapid stops. Deploying a 120 kg unit like the CRP Robot CRP-RS12-60Z40 with 400 mm Z-axis effective travel requires verifying baseplate stiffness and vertical clearance on the manufacturer datasheet prior to layout freeze.\n\nOverlooking environmental sealing or thermal limits causes drive faults and condensation damage once coolant mist enters the enclosure. Buyers must confirm on the datasheet that the Inovance IR-R16-210 S-INT provides an IP65 body and IP67 wrist, and operates between 0 °C and 45 °C at 5% RH to 95% RH non-condensing. Unsealed cell sensors also trigger false stops that disrupt overall cycle throughput.

Mechanical payload, cycle speed, and ingress criteria across listed arms

The primary sizing criteria balance maximum payload against horizontal reach and axis count. Within the listed range, the Inovance IR-R16-210 S-INT handles 16 kg and the Inovance IR-R25-178 S-INT supports 25 kg in six-axis format, while the Elite Robots CS530H reaches 30 kg over 1522 mm. For heavy planar transfers, the CRP Robot CRP-RS12-60Z40 raises maximum load capacity to 60 kg across a 1200 mm arm span.\n\nCycle timing and environmental sealing define the next two selection thresholds. On a standard door-type cycle, the CRP Robot CRP-RS12-60Z40 achieves a 0.79 s beat across 400 mm of Z-axis travel for rapid sorting. In wet or dusty machining zones, both the Inovance IR-R16-210 S-INT and the Inovance IR-R25-178 S-INT combine an IP65 body with an IP67 wrist, rated from 0 °C to 45 °C and 5% RH to 95% RH non-condensing.

Air routing, cell sensing, and auxiliary actuation criteria

Fourth, buyers evaluate internal utility routing and control networking to reduce dress-pack snagging. The Inovance IR-R16-210 S-INT and Inovance IR-R25-178 S-INT integrate a Φ8 mm internal air tube rated to 0.59 MPa pressure resistance, supplying pneumatic grippers cleanly through the arm. Meanwhile, the CRP Robot CRP-RS12-60Z40 connects over a 1 gigabit network cable for deterministic motion coordination with upstream line controllers.\n\nFifth, peripheral sensing and custom end-of-arm actuation govern cell reliability. The Lanbao CR12S cylindrical inductive sensor operates from 10 to 30 VDC at 15 mA or less with IP67 sealing and a -25 °C to 70 °C ambient rating, confirming part seating on fixtures. For custom auxiliary axes, the CubeMars T-MOTOR001173 quasi-direct drive actuator pairs an 8:1 planetary gearbox with 12.5 Nm peak torque, 9 arcmin backlash, KV 80, and class F insulation.

Quotation workflow, datasheet compatibility checks, and BOM sourcing

Atlas Electronics prepares consolidated proposals on quotation for Collaborative Robot Arms based on your part numbers, cell quantities, and operating constraints. Grouping main arms from Inovance, Elite Robots, or CRP Robot alongside peripheral sensors and auxiliary actuators on a single quotation allows procurement teams to lock technical references and budget scope across every station before issuing purchase orders.\n\nBefore order confirmation, buyers verify mechanical, electrical, and pneumatic compatibility directly against the manufacturer datasheets supplied during quoting: 10 to 30 VDC supply and NPN or PNP output logic for the Lanbao CR12S, 0.59 MPa maximum air pressure on Inovance arms, and 1 gigabit network cabling for CRP Robot cells. Atlas also sources the remaining bill of materials, including CubeMars T-MOTOR001173 actuators, capacitive sensors, cabling, and mounting accessories.

Frequently asked questions

When should a project use a 6-axis collaborative arm versus a high-payload SCARA robot?

Choose a six-axis collaborative robot arm such as the Inovance IR-R16-210 S-INT (16 kg), Inovance IR-R25-178 S-INT (25 kg), or Elite Robots CS530H (30 kg, 1522 mm reach) when parts require tilted approach angles or multi-face machine tending. Select the CRP Robot CRP-RS12-60Z40 SCARA architecture (60 kg maximum load, 1200 mm arm span, 400 mm Z-axis travel, 0.79 s standard door-type beat) when the operation consists of rapid vertical pick-and-place transfers over an open horizontal layout.

Which environmental ratings must be checked on the datasheet before placing an arm near machining coolants?

Review the manufacturer datasheet for separate body and wrist ingress ratings, ambient temperature limits, and humidity boundaries. On the Inovance IR-R16-210 S-INT and IR-R25-178 S-INT, the body carries an IP65 rating and the wrist carries an IP67 rating within 0 °C to 45 °C and 5% RH to 95% RH non-condensing. Peripheral sensors such as the Lanbao CR12S also specify IP67 protection from -25 °C to 70 °C and 35-95% RH.

How do buyers verify pneumatic and electrical compatibility between robot arms, sensors, and auxiliary actuators?

Verify internal pneumatic pressure limits, sensor supply voltage, and logic polarity before finalizing the electrical schematic. The Inovance IR-R16-210 S-INT and IR-R25-178 S-INT route air through a Φ8 mm internal tube rated up to 0.59 MPa, while the Lanbao CR12S requires 10 to 30 VDC at 15 mA or less with NPN or PNP wiring matching the robot controller inputs. If adding custom end-of-arm axes with a CubeMars T-MOTOR001173 actuator (8:1 planetary gearbox, 12.5 Nm peak torque, 9 arcmin backlash, KV 80, class F insulation), check driver voltage and feedback compatibility on its datasheet.

How does Atlas Electronics handle quotation and sourcing for the complete robot cell bill of materials?

Submit your target robot arm part numbers, cell quantities, and environmental constraints to request a consolidated proposal on quotation. Atlas Electronics quotes the main arm alongside compatible cell components and sources the rest of the bill of materials, including Lanbao CR12S inductive sensors, CubeMars T-MOTOR001173 actuators, network cabling, and peripheral hardware once you confirm the datasheet parameters.

Products mentioned

A project? Our engineers build the solution with you.

Send your requirements: Atlas proposes the architecture, the bill of materials and a quotation, then follows the supply.

Request a quotation

Related pages