Carrier board from Waveshare for Raspberry Pi Compute Modules CM4S, CM3, CM3L Lite, CM3+ and CM3+L, with expansion headers, USB ports and camera and display interfaces.
USB TO UART interfacefor serial debugging
ACT indicatorindicating the Micro SD card status
Arduino AD selection
connect 1 and 2Arduino A0-A5 as digital control pin
Arduino headerfor connecting Arduino shields
Compute Module GPIO headerbreakout all the Compute Module pins
CP2102USB TO UART converter
Product overview
Overview. The Waveshare Compute Module IO Board Plus, reference CM4S, is a carrier board for the Raspberry Pi CM4S, CM3, CM3L Lite, CM3+ and CM3+L modules. It breaks out all Compute Module pins on a dedicated GPIO header.
Main characteristics. The board provides a 5V 2.5A power port, a voltage regulator for 3.3V, 2.5V or 1.8V, an RTC battery holder supporting CR1220 batteries and a DS3231 high-precision RTC chip with I2C interface.
Interfaces and connectivity. It offers a Micro SD card slot, a USB SLAVE interface for burning the system image into the Compute Module, a CP2102 USB to UART converter for serial debugging, USB ports, a CSI camera interface for the Raspberry Pi Camera and a DSI display interface for the Raspberry Pi LCD. A Raspberry Pi GPIO header allows connecting Raspberry Pi HATs, and an Arduino header accepts Arduino shields.
Data conversion. The TLC1543 analog-to-digital converter and the DAC8552 16-bit, 2-channel digital-to-analog converter complete the board.
Typical uses. This board suits development and prototyping around Compute Modules, with access to the pins, serial interfaces and analog inputs and outputs.
Carrier board from Waveshare for Raspberry Pi Compute Modules CM4S, CM3, CM3L Lite, CM3+ and CM3+L, with expansion headers, USB ports and camera and display interfaces.
USB TO UART interfacefor serial debugging
ACT indicatorindicating the Micro SD card status
Arduino AD selection
connect 1 and 2Arduino A0-A5 as digital control pin
Arduino headerfor connecting Arduino shields
Compute Module GPIO headerbreakout all the Compute Module pins
2. Datasheet extract (recorded values)
Parameter
Value
ACT indicator
indicating the Micro SD card status
ADC/DAC configuration
config the power supply and reference voltage of ADC/DAC
Arduino AD selection
connect 1 and 2
Arduino A0-A5 as digital control pin
Arduino header
for connecting Arduino shields
BOOT selection
EN
enable the PC to access SD card/eMMC through USB SLAVE
insert a Micro SD card with pre-burnt system, to start up Compute Module 4S/3/3+ Lite variant
Peripheral configuration
config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer
Power Port
5V 2.5A
Raspberry Pi GPIO header
for connecting Raspberry Pi HATs
RTC Battery Holder
supports CR1220 batteries
TLC1543
AD converter
USB HUB enable jumper
HUB enable and USB SLAVE power selection
USB Ports
for connecting USB devices
USB SLAVE interface
allows you to burn system image in to Compute Module
USB TO UART interface
for serial debugging
VGx power selection
config the I/O level
Voltage Regulator
3.3V / 2.5V / 1.8V
Applications and use cases
Architectures in which CM4S can play a role, derived from its category. This is not a compatibility statement: check the specifications against your requirements.
A proprietary PLC locks the project into one vendor’s tools. Industrial controllers built on the Raspberry Pi Compute Module run Linux, Node-RED, Python or CODESYS on DIN rail, with I/O modules, an operator panel and a cellular router for remote access
Not every vision task justifies an industrial vision system. A Raspberry Pi with a camera module and an expansion board runs simple detection and counting models at low cost, close to the scene
To check
Frame rate and model size the board can run
Lighting and lens for the scene
Enclosure and cooling for the installation
Associated system blocks
ComputeCameras
Need a complete solution?
Send a request for CM4S and the other parts of your project.
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
What is recorded about the regulatory status and the life of this part.
Regulatory compliance
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details