DFR0504
Analog Signal Isolator for Gravity Sensors

- No-load current
- 75mA
- Response time
- 4 seconds (Typ)
- Analog Error between Two Terminals
- <± 20mV (Typ)
- Conector Type
- PH2.0-3P
Analog Signal Isolator for Gravity Sensors
DFRobot Gravity Sensor & Actuator System
DFRobot Gravity analog signal isolator module that prevents electrical interference between analog sensors, with built-in isolated 5 V power supplied directly to the sensor.
DFRobot DFR0504 analog signal isolator. Gravity series module that electrically isolates the signal and power of analog sensors to prevent interference between them.
Main characteristics. The module features built-in isolated 5 V power, which supplies the sensor directly without an external power source. Response time is 4 seconds (typ), analog error between the two terminals is less than ± 20 mV (typ), and no-load current is 75 mA. Dimensions are 42 × 32 mm.
Interfaces and connectivity. The PH2.0-3P connector is designed for DFRobot 3-pin analog sensors; the module plugs in without soldering. The analog signal transmission ratio is 1:1, which limits the impact on the sensor output signal.
Power and environment. Operating voltage is 5.0 V. The non-isolated MCU terminal must receive a precise voltage of 5.0 ± 0.1 V; external power for the Arduino board is recommended to guarantee sufficient current and voltage precision. The maximum output current from the SEN terminal is 170 mA. The MCU and SEN grounds are isolated from each other and must not be short-circuited. The isolator generating heat during operation is normal.
Typical uses. Module suited to preventing interference between sensors, for example in a multi-parameter water quality monitoring system where pH and conductivity sensors must not disturb each other. It is compatible with almost all DFRobot analog sensors and requires no change to the main board code.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for DFR0504, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Response time | 4 seconds (Typ) |
| Analog Error between Two Terminals | <± 20mV (Typ) |
| Conector Type | PH2.0-3P |
| Dimension | 42 * 32mm / 1.65 * 1.26 inch |
| Gravity | Analog Signal Isolator |
| No-load current | 75mA |
| Operating Voltage | 5.0V |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for DFR0504. For a missing document or a specific revision, our experts send it to you.
DFRobot Gravity analog signal isolator module that prevents electrical interference between analog sensors, with built-in isolated 5 V power supplied directly to the sensor.
| Parameter | Value |
|---|---|
| Response time | 4 seconds (Typ) |
| Analog Error between Two Terminals | <± 20mV (Typ) |
| Conector Type | PH2.0-3P |
| Dimension | 42 * 32mm / 1.65 * 1.26 inch |
| Gravity | Analog Signal Isolator |
| No-load current | 75mA |
| Operating Voltage | 5.0V |
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
Analog Signal Isolator for Gravity Sensors

Gravity: I2C 8x16 RGB LED Matrix Panel

Gravity: 1602 LCD Keypad Shield For Arduino

Gravity: Nano I/O Shield for Arduino Nano

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | DFR0504 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details