SEN0262
Analog current-to-voltage converter for 4-20 mA loop

- Detection range
- 0~25mA DC
- Supply voltage
- 3.3~5.5V
- Connector Type
- PH2.0-3P
- Product Size
- 30mm * 22mm (1.18inch * 0.87inch)
Analog current-to-voltage converter for 4-20 mA loop
DFRobot Gravity Sensor & Actuator System
DFRobot SEN0262 module converting a 0-25 mA current signal into a 0-3 V voltage, to read 4-20 mA industrial sensors with a control board.
Overview. The DFRobot SEN0262 analog current-to-voltage converter is a module that converts a DC current signal from 0 to 25 mA into a voltage signal from 0 to 3 V. It is designed for 4-20 mA current output sensors and lets a main control board easily read these industrial signals.
Main characteristics. The module uses a 0.1% high precision sense resistor and an ultra-low noise rail-to-rail zero-drift operational amplifier, giving high accuracy without calibration. Its wide 0-25 mA measurement range covers both fault detection (current below 4 mA) and overrun detection (current above 20 mA). Measurement accuracy is ±0.5% F.S. with a 16-bit ADC and ±2% F.S. with a 10-bit ADC. The termination resistance is 120 Ω.
Power supply and dimensions. The module operates with a supply voltage of 3.3 to 5.5 V. Its size is 30 mm × 22 mm. It is supplied with a PH2.0-3P connector type and a 3-pin digital sensor cable.
Typical uses. With its 0-3 V output compatible with most control boards, it suits fault and overrun detection on industrial current loops. For high-precision measurement (15-bit resolution), it can be combined with the Gravity I2C high-precision ADC module, according to the manufacturer's documentation.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for SEN0262, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Supply voltage | 3.3~5.5V |
| Connector Type | PH2.0-3P |
| Detection range | 0~25mA DC |
| Gravity | Analog Current to Voltage Converter(for 4~20mA Application) |
| Measurement Accuracy | ±0.5% F.S. @ 16-bit ADC, ±2% F.S. @ 10-bit ADC |
| Product Size | 30mm * 22mm (1.18inch * 0.87inch) |
| Termination Resistance | 120Ω |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for SEN0262. For a missing document or a specific revision, our experts send it to you.
DFRobot SEN0262 module converting a 0-25 mA current signal into a 0-3 V voltage, to read 4-20 mA industrial sensors with a control board.
| Parameter | Value |
|---|---|
| Supply voltage | 3.3~5.5V |
| Connector Type | PH2.0-3P |
| Detection range | 0~25mA DC |
| Gravity | Analog Current to Voltage Converter(for 4~20mA Application) |
| Measurement Accuracy | ±0.5% F.S. @ 16-bit ADC, ±2% F.S. @ 10-bit ADC |
| Product Size | 30mm * 22mm (1.18inch * 0.87inch) |
| Termination Resistance | 120Ω |
Points to check before using SEN0262 in a design. They are derived from the recorded characteristics, not from the manufacturer's application circuits.
| Supply voltage | 3.3~5.5V |
Check the exact pin assignment and the application circuit in the datasheet, or ask our experts.
Answers to the questions that the recorded characteristics of SEN0262 can answer. A question is not asked when nothing is recorded to answer it.
3.3~5.5V (source: Supply voltage).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
Analog current-to-voltage converter for 4-20 mA loop

Gravity: 7/24 Industrial Analog pH Meter Kit V2 (Arduino, Raspberry Pi)

Gravity: 1602 LCD Keypad Shield For Arduino

Gravity: Nano I/O Shield for Arduino Nano

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | SEN0262 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details