HK75
Smart capacitance differential pressure transmitter 4-20 mA HART

- Alarm current default setting
- 21 mA
- Storage Temperature
- -40℃ ~105℃
- Ambient temperature
- -40℃ ~85℃
- Ambient temperature influence
- ≤±0.04%URL/10℃
Smart capacitance differential pressure transmitter 4-20 mA HART
Industrial Pressure Transmitters (4-20mA / IO-Link)
Holykell HK75 differential pressure transmitter with monocrystalline silicon sensor for measuring gas, steam and liquids, with 4-20 mA output and superimposed HART digital signal.
Overview. The Holykell HK75 differential pressure transmitter is a smart capacitance transmitter fitted with a monocrystalline silicon pressure sensor. It measures differential pressure in gases, steam and liquids, and can also be used for level, volume or mass measurements in liquids.
Accuracy and stability. Accuracy is ±0.2%, ±0.075% or ±0.1% (including linearity, hysteresis and repeatability from zero). Stability is ±0.1% over 3 years. Ambient temperature influence is ≤±0.04% URL/10°C and static pressure influence is ±0.05%/10 MPa.
Output and communication. Two-wire 4-20 mA output in line with the NAMUR NE43 specification, with a superimposed digital signal using the HART protocol. The output can be linear or square root. In case of sensor or circuit failure, the automatic diagnosis outputs 3.9 mA or 21.0 mA, the value being presettable by the user (21 mA by default).
Power and environment. Power supply 12-36 V DC (24 V DC recommended). Ambient temperature -40°C to 85°C, measuring medium temperature -40°C to 120°C, storage temperature -40°C to 105°C. Housing rated IP67. LCD or OLED display.
Typical uses. Differential pressure measurement on gas and steam, level, volume or mass measurement on liquids, in process control and monitoring installations, integrated into a 4-20 mA loop or a HART network.
Integration. Measuring range and zero point can be set to any value within the measurement range; selecting the range code with the lowest possible turndown ratio is recommended to optimise performance. A change in installation position perpendicular to the diaphragm surface does not cause zero drift.
Note. Pressure ranges, process connections and other options are defined by the configuration requested on quotation.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for HK75, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Response time | High alarm mode The damping constant of the amplifier component is 0.1s; the time constant of the |
| Accuracy | ±0.2%,±0.075%,±0.1%; (Including linearity, hysteresis and repeatability from zero) |
| Alarm Current | If the sensor or circuit fails, the automatic diagnosis function will automatically output 3.9 or 21.0mA (user can pre-set) |
| Alarm current default setting | 21 mA |
| Ambient temperature | -40℃ ~85℃ |
| Ambient temperature influence | ≤±0.04%URL/10℃ |
| Display | LCD, OLED |
| Fault warning | Imin=3.9mA, Imax=21.0mA |
| High report mode (maximum) | Low alarm mode (minimum): 3.9mA |
| Influence of installation location | range in the table, as long as: calibration range ≥ minimum range The change of the installation position perpendicular to the diaphragm surface will not cause the zero drift effect. If the installation position and the diaphragm surface change more than 90°, the zero position in the range of <0.4kPa will be affected. It can be adjusted by adjusting the zero and there is no impact on the |
| Influence of static pressure | ±0.05%/10MPa |
| IP Rating for Housing | IP67 |
| Measuring medium | Gas, steam, liquid |
| Measuring medium temperature | -40℃~120℃ |
| Medium temperature | -40℃ ~85℃ |
| Module temperature shown on display | -20℃~70℃ (LCD), -40℃~80℃ (OLED) |
| Output | range. Two-wire system 4-20mA, in line with NAMIR NE43 specification, superimposed digital signal (Hart protocol) |
| Output signal limit | Linear or square root output is optional. |
| Power influence | ±0.001%/10V, which can be negligible |
| Power supply | 12-36 V DC(24Vdc recommended) |
| Range limit | Within the upper and lower limits of the measuring range, it can be adjusted |
| Stability | ±0.1%/3 years |
| Storage Temperature | -40℃ ~105℃ |
| Zero point setting | arbitrarily. It is recommended to select a range code with the lowest possible turndown ratio to optimize performance Zero point and range can be adjusted to any value within the measurement |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for HK75. For a missing document or a specific revision, our experts send it to you.
Holykell HK75 differential pressure transmitter with monocrystalline silicon sensor for measuring gas, steam and liquids, with 4-20 mA output and superimposed HART digital signal.
| Parameter | Value |
|---|---|
| Response time | High alarm mode The damping constant of the amplifier component is 0.1s; the time constant of the |
| Accuracy | ±0.2%,±0.075%,±0.1%; (Including linearity, hysteresis and repeatability from zero) |
| Alarm Current | If the sensor or circuit fails, the automatic diagnosis function will automatically output 3.9 or 21.0mA (user can pre-set) |
| Alarm current default setting | 21 mA |
| Ambient temperature | -40℃ ~85℃ |
| Ambient temperature influence | ≤±0.04%URL/10℃ |
| Display | LCD, OLED |
| Fault warning | Imin=3.9mA, Imax=21.0mA |
| High report mode (maximum) | Low alarm mode (minimum): 3.9mA |
| Influence of installation location | range in the table, as long as: calibration range ≥ minimum range The change of the installation position perpendicular to the diaphragm surface will not cause the zero drift effect. If the installation position and the diaphragm surface change more than 90°, the zero position in the range of <0.4kPa will be affected. It can be adjusted by adjusting the zero and there is no impact on the |
| Influence of static pressure | ±0.05%/10MPa |
| IP Rating for Housing | IP67 |
| Measuring medium | Gas, steam, liquid |
| Measuring medium temperature | -40℃~120℃ |
| Medium temperature | -40℃ ~85℃ |
| Module temperature shown on display | -20℃~70℃ (LCD), -40℃~80℃ (OLED) |
| Output | range. Two-wire system 4-20mA, in line with NAMIR NE43 specification, superimposed digital signal (Hart protocol) |
| Output signal limit | Linear or square root output is optional. |
| Power influence | ±0.001%/10V, which can be negligible |
| Power supply | 12-36 V DC(24Vdc recommended) |
| Range limit | Within the upper and lower limits of the measuring range, it can be adjusted |
| Stability | ±0.1%/3 years |
| Storage Temperature | -40℃ ~105℃ |
| Zero point setting | arbitrarily. It is recommended to select a range code with the lowest possible turndown ratio to optimize performance Zero point and range can be adjusted to any value within the measurement |
Answers to the questions that the recorded characteristics of HK75 can answer. A question is not asked when nothing is recorded to answer it.
Yes — recorded under "Alarm Current": If the sensor or circuit fails, the automatic diagnosis function will automatically output 3.9 or 21.0mA (user can pre-set).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
Smart capacitance differential pressure transmitter 4-20 mA HART

Monocrystalline Differential Pressure Transmitter

SUP-P300 Pressure transmitter with compact size for universal use

SUP-P350K Hygienic pressure transmitter

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | HK75 |
| Manufacturer | Holykell |
Industrial Pressure Transmitters (4-20mA / IO-Link)
ATEX pressure transmitter with flush diaphragm · Ref. : MPM489
Price on request
Industrial Pressure Transmitters (4-20mA / IO-Link)
Monocrystal Silicon Differential Pressure Transmitter 4-20mA · Ref. : HPT708
Price on request
Industrial Pressure Transmitters (4-20mA / IO-Link)
Gauge Pressure Transmitter for Industrial Process
Price on request
Industrial Pressure Transmitters (4-20mA / IO-Link)
Industrial pressure transmitter 4-20 mA HART RS485 Modbus · Ref. : 35723348-00
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details