DFR0553
16-Bit I2C ADC Module for Raspberry Pi and Arduino

- Analog Signal Detection Range
- 0~VCC
- Interface Level
- High 3.3V, Low 0V
- Interface Type
- Gravity I2C
- Supply Voltage (VCC)
- 3.3~5.0V
16-Bit I2C ADC Module for Raspberry Pi and Arduino
DFRobot Gravity Sensor & Actuator System
DFRobot 16-bit analog-to-digital converter module with Gravity I2C interface, letting a Raspberry Pi or Arduino read Gravity analog sensors across 4 channels.
Overview. The DFR0553 from DFRobot is a 16-bit analog-to-digital converter (ADC) module with a Gravity I2C interface, designed for Raspberry Pi and Arduino boards. It lets them read signals from the analog sensors of the Gravity range, which Raspberry Pi GPIO pins cannot read directly.
Main characteristics. The module uses the ADS1115 chip and provides 4 analog channels. Its analog signal detection range is 0 to VCC. It operates from a 3.3 to 5.0 V supply and draws 2 to 3 mA excluding the sensor. Its size is 32 mm × 32 mm.
Interfaces and connectivity. The connection uses a Gravity I2C interface with a 3.3 V high level and 0 V low level. Colour-coded 3-pin headers allow direct plug-in to Gravity sensors. An on-board I2C address selection switch supports cascading two modules to read 8 channels.
Typical uses. The module suits reading analog sensors on a Raspberry Pi or Arduino, particularly where accurate acquisition of weak or highly variable signals is required.
Integration. The kit includes the module, one XH2.54 4-pin header and one Gravity-4P I2C/UART sensor wire. Note that the voltage on analog input pins must be less than VCC + 0.3 V.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for DFR0553, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| ADC | 16 Bit |
| Analog Signal Detection Range | 0~VCC |
| Gravity | I2C ADS1115 16-Bit ADC Module (Arduino & Raspberry Pi Compatible) |
| Interface Level | High 3.3V, Low 0V |
| Interface Type | Gravity I2C |
| Number of Analog Channels | 4 |
| Operating Current | 2~3mA (Not include sensor module) |
| Product Size | 32mm * 32mm(1.26in*1.26in) |
| Supply Voltage (VCC) | 3.3~5.0V |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for DFR0553. For a missing document or a specific revision, our experts send it to you.
DFRobot 16-bit analog-to-digital converter module with Gravity I2C interface, letting a Raspberry Pi or Arduino read Gravity analog sensors across 4 channels.
| Parameter | Value |
|---|---|
| ADC | 16 Bit |
| Analog Signal Detection Range | 0~VCC |
| Gravity | I2C ADS1115 16-Bit ADC Module (Arduino & Raspberry Pi Compatible) |
| Interface Level | High 3.3V, Low 0V |
| Interface Type | Gravity I2C |
| Number of Analog Channels | 4 |
| Operating Current | 2~3mA (Not include sensor module) |
| Product Size | 32mm * 32mm(1.26in*1.26in) |
| Supply Voltage (VCC) | 3.3~5.0V |
Points to check before using DFR0553 in a design. They are derived from the recorded characteristics, not from the manufacturer's application circuits.
| Operating Current | 2~3mA (Not include sensor module) |
| Supply Voltage (VCC) | 3.3~5.0V |
Check the exact pin assignment and the application circuit in the datasheet, or ask our experts.
Answers to the questions that the recorded characteristics of DFR0553 can answer. A question is not asked when nothing is recorded to answer it.
Yes — recorded under "Gravity": I2C ADS1115 16-Bit ADC Module (Arduino & Raspberry Pi Compatible).
3.3~5.0V (source: Supply Voltage (VCC)).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
16-Bit I2C ADC Module for Raspberry Pi and Arduino

Gravity: 1602 LCD Keypad Shield For Arduino

Gravity: Nano I/O Shield for Arduino Nano

Gravity: DS18B20 Temperature Sensor (Arduino Compatible)

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | DFR0553 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details