SEN0231
Formaldehyde (HCHO) Sensor with Gravity Interface

- Operating temperature
- 0~50℃
- Detection range
- 0~5ppm
- Interface Type
- Gravity-3Pin
- Input Voltage
- 3.3~6V
Formaldehyde (HCHO) Sensor with Gravity Interface
DFRobot Gravity Sensor & Actuator System
Formaldehyde (HCHO) sensor module compatible with Arduino and Raspberry Pi, intended for indoor air quality monitoring.
Overview. The DFRobot SEN0231 is a formaldehyde (HCHO) sensor in a module compatible with Arduino and Raspberry Pi. It measures the formaldehyde concentration in the air and enables real-time air quality monitoring, for example in indoor air quality monitoring or real-time air quality monitoring stations.
Main characteristics. Detection range of 0 to 5 ppm with a resolution of 0.01 ppm. Warm-up time of 3 minutes or less, response time and resume time of 60 seconds or less. Working life of 2 years in air. The sensor offers high stability and strong anti-jamming capability.
Interfaces and connectivity. Gravity 3-pin connector. Selectable output: DAC signal of 0.4 to 2 V for 0 to 5 ppm, or UART at 9600 baud.
Power and environment. Input voltage of 3.3 to 6 V. Operating temperature and storage temperature of 0 to 50 °C. Operating humidity of 15% RH to 90% RH, no condensation. Interfering gases: alcohol, CO, etc. Dimensions 38 × 28 × 15 mm.
Typical uses. Indoor air quality monitoring, real-time monitoring stations, DIY formaldehyde detector.
Integration. The module connects directly to an Arduino or Raspberry Pi board, with sample code provided by the manufacturer for quick implementation.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for SEN0231, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Response time | ≤60 seconds |
| Operating temperature | 0~50℃ |
| Detection range | 0~5ppm |
| Dimension | 38*28*15mm/1.50*1.10*0.59inches |
| Gravity | Formaldehyde (HCHO) Sensor |
| Input Voltage | 3.3~6V |
| Interface Type | Gravity-3Pin |
| Interference Gas | Alcohol, CO & etc |
| Operating Hum | 15%RH-90%RH(No Condensation) |
| Output signal | Optional DAC(0.4~2V,for 0-5ppm) or UART(9600) |
| Resolution | 0.01ppm |
| Resume Time | ≤60 seconds |
| Storage Temp | 0~50℃ |
| Target gas | HCHO |
| Warm-Up Time | ≤3 minutes |
| Working Life | 2 years(in air) |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for SEN0231. For a missing document or a specific revision, our experts send it to you.
Formaldehyde (HCHO) sensor module compatible with Arduino and Raspberry Pi, intended for indoor air quality monitoring.
| Parameter | Value |
|---|---|
| Response time | ≤60 seconds |
| Operating temperature | 0~50℃ |
| Detection range | 0~5ppm |
| Dimension | 38*28*15mm/1.50*1.10*0.59inches |
| Gravity | Formaldehyde (HCHO) Sensor |
| Input Voltage | 3.3~6V |
| Interface Type | Gravity-3Pin |
| Interference Gas | Alcohol, CO & etc |
| Operating Hum | 15%RH-90%RH(No Condensation) |
| Output signal | Optional DAC(0.4~2V,for 0-5ppm) or UART(9600) |
| Resolution | 0.01ppm |
| Resume Time | ≤60 seconds |
| Storage Temp | 0~50℃ |
| Target gas | HCHO |
| Warm-Up Time | ≤3 minutes |
| Working Life | 2 years(in air) |
Points to check before using SEN0231 in a design. They are derived from the recorded characteristics, not from the manufacturer's application circuits.
| Input Voltage | 3.3~6V |
Check the exact pin assignment and the application circuit in the datasheet, or ask our experts.
Answers to the questions that the recorded characteristics of SEN0231 can answer. A question is not asked when nothing is recorded to answer it.
0~50℃ (source: Operating temperature).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
Formaldehyde (HCHO) Sensor with Gravity Interface

Gravity: 1602 LCD Keypad Shield For Arduino

Gravity: Nano I/O Shield for Arduino Nano

Gravity: DS18B20 Temperature Sensor (Arduino Compatible)

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | SEN0231 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details