SEN0257
Analog Water Pressure Sensor 0–1.6 MPa with 0.5–4.5 V Output

- Operating Temperature
- -20~85°C
- Pressure Measurement Range
- 0~1.6 Mpa
- Input Voltage
- +5 VDC
- Quiescent Current
- 2.8 mA
Analog Water Pressure Sensor 0–1.6 MPa with 0.5–4.5 V Output
DFRobot Gravity Sensor & Actuator System
Analog pressure sensor for non-corrosive liquids and gases with a 0.5–4.5 V linear output over 0–1.6 MPa. It measures pressure in water circuits such as household plumbing, irrigation or tanks.
Overview. The SEN0257 analog water pressure sensor from DFRobot is a Gravity-series pressure sensor for non-corrosive liquids and gases. It converts the measured pressure into a linear voltage signal of 0.5 to 4.5 V that a controller can read for display, logging or control logic.
Main characteristics. The measurement range is 0 to 1.6 MPa, with an accuracy of 0.5% to 1% FS (0.5% between 0 and 55 °C). The response time is below 2.0 ms, the normal operating pressure is at most 2.0 MPa and the damaged pressure is at least 3.0 MPa.
Interfaces and connectivity. The sensor uses a Gravity 3-pin wiring (signal, VCC, GND) with a 1 m line, allowing direct connection to a compatible board. Its analog output is the 0.5–4.5 V signal.
Power and environment. The input voltage is +5 VDC. The operating temperature range is -20 to 85 °C and the waterproof level is IP68. The medium is liquid or gas without corrosion.
Installation. The sensor has a G1/4 thread and ships with a mounted G1/2-to-G1/4 adapter, giving two fitting options.
Typical uses. This sensor suits pressure measurement in water installations such as household plumbing, garden irrigation, farm water systems and tanks, and integration into custom water monitoring and control systems combined with a solenoid valve and other sensors.
Integration. The analog signal connects to an analog input of a controller, with a Gravity IO Expansion Shield documented as a compatible interface. Available on quotation from Atlas Electronics.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for SEN0257, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Response time | <2.0 ms |
| Output voltage | 0.5~4.5 V |
| Adapter | G1/2 to G1/4 |
| Damaged Pressure | ≥3.0Mpa |
| Gravity | Analog Water Pressure Sensor (0–16bar, G1/4, 5V) |
| Input Voltage | +5 VDC |
| Line Length | 1m |
| Measurement Accuracy | 0.5%~1%FS (0.5%, 0~55°C) |
| Medium | liquid/gas without corrosion |
| Normal Operating Pressure | ≤2.0 Mpa |
| Operating Temperature | -20~85°C |
| Pressure Measurement Range | 0~1.6 Mpa |
| Quiescent Current | 2.8 mA |
| Service Life | 10’000’000 times |
| Threadably | G1/4 |
| Waterproof level | IP68 |
| Wiring | Gravity-3Pin (Signal-VCC-GND) |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for SEN0257. For a missing document or a specific revision, our experts send it to you.
Analog pressure sensor for non-corrosive liquids and gases with a 0.5–4.5 V linear output over 0–1.6 MPa. It measures pressure in water circuits such as household plumbing, irrigation or tanks.
| Parameter | Value |
|---|---|
| Response time | <2.0 ms |
| Output voltage | 0.5~4.5 V |
| Adapter | G1/2 to G1/4 |
| Damaged Pressure | ≥3.0Mpa |
| Gravity | Analog Water Pressure Sensor (0–16bar, G1/4, 5V) |
| Input Voltage | +5 VDC |
| Line Length | 1m |
| Measurement Accuracy | 0.5%~1%FS (0.5%, 0~55°C) |
| Medium | liquid/gas without corrosion |
| Normal Operating Pressure | ≤2.0 Mpa |
| Operating Temperature | -20~85°C |
| Pressure Measurement Range | 0~1.6 Mpa |
| Quiescent Current | 2.8 mA |
| Service Life | 10’000’000 times |
| Threadably | G1/4 |
| Waterproof level | IP68 |
| Wiring | Gravity-3Pin (Signal-VCC-GND) |
Points to check before using SEN0257 in a design. They are derived from the recorded characteristics, not from the manufacturer's application circuits.
| Output voltage | 0.5~4.5 V |
| Input Voltage | +5 VDC |
| Quiescent Current | 2.8 mA |
Check the exact pin assignment and the application circuit in the datasheet, or ask our experts.
Answers to the questions that the recorded characteristics of SEN0257 can answer. A question is not asked when nothing is recorded to answer it.
-20~85°C (source: Operating Temperature).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
Analog Water Pressure Sensor 0–1.6 MPa with 0.5–4.5 V Output

Gravity: 1602 LCD Keypad Shield For Arduino

Gravity: Nano I/O Shield for Arduino Nano

Gravity: DS18B20 Temperature Sensor (Arduino Compatible)

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | SEN0257 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details