SEN0496
Electrochemical oxygen O2 sensor 0-100 %Vol with I2C output

- Operating Temperature Range
- -20°C ~ +50°C
- Working pressure range
- 0.5~2.0Bar
- Operating Humidity Range
- 0-99% RH (non-condensing)
- Measuring Range
- 0~100%
Electrochemical oxygen O2 sensor 0-100 %Vol with I2C output
DFRobot Gravity Sensor & Actuator System
Electrochemical oxygen O2 concentration sensor with I2C output, measuring from 0 to 100 %Vol, for detecting oxygen in air and gases.
Overview. The DFRobot SEN0496 is an electrochemical oxygen O2 concentration sensor measuring from 0 to 100 %Vol, with a digital I2C output. It uses an AO2 CiTiceL® oxygen sensor probe and a calibration algorithm built into the signal board, allowing manual single-point or double-point calibration.
Main characteristics. Based on the electrochemical principle, the sensor offers strong anti-interference ability and high sensitivity. Its response time is less than 5 s and its lifespan is more than 2 years in air. Its working pressure range is 0.5 to 2.0 bar.
Interfaces and connectivity. The output is I2C and the working voltage is 3.3 to 5.5 V DC. The sensor plugs into a Gravity interface and is compatible with Arduino, ESP32 and Raspberry Pi controllers.
Power and environment. The operating temperature range is -20 °C to +50 °C, and the operating humidity range is 0 to 99 % RH, non-condensing. The sensor measures 32 mm × 27 mm, with a mounting hole of 3.1 mm inner diameter and 6 mm outer diameter.
Typical uses. This sensor suits oxygen generators, automobile exhaust oxygen detection and air-fuel ratio detection. Exposure to high concentrations of solvent vapours should be avoided during storage, fitting and operation.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for SEN0496, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Response time | <5S |
| Gravity | Electrochemical Oxygen / O2 Sensor (0-100%Vol, I2C) |
| Lifespan | >2 years (in air) |
| Measuring Range | 0~100% |
| Mounting Hole Size | inner diameter 3.1mm(0.12 inch)/outer diameter 6mm(0.24 inch) |
| Operating Humidity Range | 0-99% RH (non-condensing) |
| Operating Temperature Range | -20°C ~ +50°C |
| Output signal | I2C |
| Physical Quantity Detected | Oxygen / O2 concentration |
| Size | 32mm*27mm/1.26*1.06 inch |
| Working pressure range | 0.5~2.0Bar |
| Working voltage | 3.3~5.5V DC |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for SEN0496. For a missing document or a specific revision, our experts send it to you.
Electrochemical oxygen O2 concentration sensor with I2C output, measuring from 0 to 100 %Vol, for detecting oxygen in air and gases.
| Parameter | Value |
|---|---|
| Response time | <5S |
| Gravity | Electrochemical Oxygen / O2 Sensor (0-100%Vol, I2C) |
| Lifespan | >2 years (in air) |
| Measuring Range | 0~100% |
| Mounting Hole Size | inner diameter 3.1mm(0.12 inch)/outer diameter 6mm(0.24 inch) |
| Operating Humidity Range | 0-99% RH (non-condensing) |
| Operating Temperature Range | -20°C ~ +50°C |
| Output signal | I2C |
| Physical Quantity Detected | Oxygen / O2 concentration |
| Size | 32mm*27mm/1.26*1.06 inch |
| Working pressure range | 0.5~2.0Bar |
| Working voltage | 3.3~5.5V DC |
Points to check before using SEN0496 in a design. They are derived from the recorded characteristics, not from the manufacturer's application circuits.
| Working voltage | 3.3~5.5V DC |
Check the exact pin assignment and the application circuit in the datasheet, or ask our experts.
Answers to the questions that the recorded characteristics of SEN0496 can answer. A question is not asked when nothing is recorded to answer it.
Yes — recorded under "Gravity": Electrochemical Oxygen / O2 Sensor (0-100%Vol, I2C).
-20°C ~ +50°C (source: Operating Temperature Range).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
Electrochemical oxygen O2 sensor 0-100 %Vol with I2C output

Gravity: 1602 LCD Keypad Shield For Arduino

Gravity: Nano I/O Shield for Arduino Nano

Gravity: DS18B20 Temperature Sensor (Arduino Compatible)

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | SEN0496 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details