SEN0467
H2S Hydrogen Sulfide Sensor Calibrated I2C and UART

- Detection range
- 0~100ppm
- Working current
- <5mA
- Storage humidity
- 15~90%RH (non-condensing)
- Storage Temperature
- -20~50℃
H2S Hydrogen Sulfide Sensor Calibrated I2C and UART
DFRobot Gravity Sensor & Actuator System
Factory-calibrated electrochemical hydrogen sulfide (H2S) sensor with analog, I2C and UART outputs, for H2S detection over a range of 0 to 100 ppm.
DFRobot SEN0467 H2S sensor. The DFRobot SEN0467 is a hydrogen sulfide (H2S) sensor from the Gravity range, factory-calibrated, which measures H2S concentration in the environment over a range of 0 to 100 ppm.
Principle and characteristics. The sensor uses the electrochemical principle. It offers strong anti-interference ability, high stability and high sensitivity. Its service life is more than 2 years in the air. It integrates a temperature compensation algorithm and a threshold alarm function.
Interfaces and connectivity. Three output modes are available: I2C, UART (0 to 3 V) and analog voltage. The sensor provides 32 modifiable I2C addresses, allowing several sensors on one bus.
Power and environment. The working voltage is 3.3 to 5.5 V DC for a current below 5 mA. Working conditions are -20 to 50 ℃ and 15 to 90 %RH non-condensing. Storage is within the same temperature and humidity ranges.
Typical uses. The sensor suits hydrogen sulfide detection in underground, industrial and environmental protection devices.
Integration. The Gravity signal conversion board, the sensor probe and a 4-pin cable are supplied. The sensor is compatible with Arduino, ESP32 and Raspberry Pi, and uses the same data format as the other gas sensors of the DFRobot series.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for SEN0467, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| Adapter Plate Size | 37*32mm |
| Compatibility | Arduino, ESP32, Raspberry pi |
| Detection Gas | Hydrogen sulfide (H2S) |
| Detection range | 0~100ppm |
| Gravity | H2S Sensor (Calibrated) - I2C & UART |
| Lifespan | >2 years (in the air) |
| Output signal | I2C, UART (0~3V), analog voltage |
| Storage humidity | 15~90%RH (non-condensing) |
| Storage Temperature | -20~50℃ |
| Working current | <5mA |
| Working humidity | 15~90%RH (non-condensing) |
| Working temperature | -20~50℃ |
| Working voltage | 3.3~5.5V DC |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for SEN0467. For a missing document or a specific revision, our experts send it to you.
Factory-calibrated electrochemical hydrogen sulfide (H2S) sensor with analog, I2C and UART outputs, for H2S detection over a range of 0 to 100 ppm.
| Parameter | Value |
|---|---|
| Adapter Plate Size | 37*32mm |
| Compatibility | Arduino, ESP32, Raspberry pi |
| Detection Gas | Hydrogen sulfide (H2S) |
| Detection range | 0~100ppm |
| Gravity | H2S Sensor (Calibrated) - I2C & UART |
| Lifespan | >2 years (in the air) |
| Output signal | I2C, UART (0~3V), analog voltage |
| Storage humidity | 15~90%RH (non-condensing) |
| Storage Temperature | -20~50℃ |
| Working current | <5mA |
| Working humidity | 15~90%RH (non-condensing) |
| Working temperature | -20~50℃ |
| Working voltage | 3.3~5.5V DC |
Answers to the questions that the recorded characteristics of SEN0467 can answer. A question is not asked when nothing is recorded to answer it.
Yes — recorded under "Gravity": H2S Sensor (Calibrated) - I2C & UART.
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
H2S Hydrogen Sulfide Sensor Calibrated I2C and UART

Gravity: CL2 Sensor (Calibrated) - I2C & UART

Gravity: NH3 Sensor (Calibrated) - I2C & UART

Gravity: 1602 LCD Keypad Shield For Arduino

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | SEN0467 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details