SEN0696
10DOF IMU Sensor with Accelerometer, Gyroscope, Magnetometer and Barometer

- Measurement Range
- ±2000 µT
- Pressure Measurement Range
- 30 kPa ~ 125 kPa
- Temperature measurement range
- -40 °C ~ +85 °C
- Communication interface
- I²C / UART
10DOF IMU Sensor with Accelerometer, Gyroscope, Magnetometer and Barometer
DFRobot Gravity Sensor & Actuator System
DFRobot Gravity 10DOF IMU module combining accelerometer, gyroscope, magnetometer and barometer, with I2C or UART interface, for motion, heading and altitude change measurement.
Overview. The DFRobot Gravity 10DOF IMU sensor SEN0696 is an inertial measurement module combining three Bosch sensors: BMI323, BMM350 and BMP581. It provides 3-axis acceleration, 3-axis angular velocity, 3-axis magnetic field and barometric pressure data.
Main characteristics. The accelerometer offers ranges of ±2 g, ±4 g, ±8 g and ±16 g, with a sensitivity of 16384 LSB/g for the ±2 g range. The gyroscope measures at ±125, ±250, ±500, ±1000 and ±2000 °/s. The magnetometer covers ±2000 µT with a resolution of approximately 0.1 µT. The barometer measures from 30 kPa to 125 kPa with a resolution of approximately 0.0156 Pa and a typical relative accuracy of ±6 Pa between 700 and 1100 hPa. ADC resolution is 16-bit.
Interfaces and connectivity. The module communicates over I²C with four possible addresses (0x4A by default, 0x4B, 0x4C, 0x4D) or over UART. The connector is PH2.0-4P with Gravity pinout, with additional 2.54 mm pin header holes. Four programmable interrupt pins are provided.
Power and environment. The operating voltage is DC 3.3–5 V, with an operating current of 3.59 mA. The temperature measurement range is -40 °C to +85 °C, with an absolute accuracy of ±0.5 K within -5 to 55 °C. The module supports normal periodic measurement, triggered forced measurement and low-power sleep standby modes.
Typical uses. The module suits motion and orientation monitoring for indoor robots, floor or ramp change detection, elevation logging on wearable devices, and multi-sensor algorithm development. It is compatible with Arduino, Raspberry Pi and ESP32 boards.
Integration. An integrated DFRobot library and the Gravity GUI simplify bring-up before application code is written. The product is available on quotation from Atlas Electronics.
No published question about this part yet. Questions are reviewed before publication.
Every characteristic recorded for SEN0696, with where it comes from. Use the filters to find one quickly.
| Characteristic | Value |
|---|---|
| ADC Resolution | 16-bit |
| Angular Rate Ranges | ±125, ±250, ±500, ±1000, ±2000 °/s |
| Communication interface | I²C / UART |
| Connector Type | PH2.0-4P (Gravity pinout) / 2.54 mm pin header holes |
| Forced Mode Maximum Trigger Frequency | 200 Hz (avg=0 only) |
| Gravity | 10DOF IMU Sensor for Motion, Heading & Altitude Changes (I2C / UART, Plug & Play) |
| I²C Addresses | 0x4A (default), 0x4B, 0x4C, 0x4D |
| Magnetic Field Resolution | approx. 0.1 µT |
| Measurement Range | ±2000 µT |
| Measurement Ranges | ±2 g, ±4 g, ±8 g, ±16 g |
| Mounting hole diameter | 3 mm |
| Mounting Hole Spacing | 20 mm |
| Normal Mode Output Data Rate | 400/200/100/50/25/12.5/6.25/3.125/1.5625 Hz, typical deviation ±2% |
| Offset Temperature Error | ±200 nT/K |
| Operating Current | 3.59 mA |
| Operating Modes | Normal periodic measurement, triggered forced measurement, low-power sleep standby |
| Operating Voltage | DC 3.3–5 V |
| Output Data Rate (ODR) | High Performance / Normal mode: 12.5 Hz ~ 6400 Hz Low Power mode: 0.78125 Hz ~ 400 Hz |
| PCB Size | 32 mm × 27 mm |
| Pressure Long-Term Annual Drift | ±10 Pa |
| Pressure Measurement Range | 30 kPa ~ 125 kPa |
| Pressure Relative Accuracy | typical ±6 Pa within 700~1100 hPa, 15~55 °C |
| Pressure Resolution | approx. 0.0156 Pa |
| Pressure Temperature-Induced Offset | ±0.5 Pa/K |
| Programmable Interrupt Pins | ×4 |
| Sensitivity | ±2 g range: 16384 LSB/g ±4 g range: 8192 LSB/g ±8 g range: 4096 LSB/g ±16 g range: 2048 LSB/g |
| Sensitivity Error | ±0.5% |
| Sensitivity Temperature Drift | ±0.010 %/K |
| Temperature Absolute Accuracy | ±0.5 K within -5~55 °C and over full temperature range |
| Temperature measurement range | -40 °C ~ +85 °C |
| Temperature Resolution | approx. 0.000015 °C |
| X/Y-Axis Gain Error | ±1% (25 °C, after API compensation) |
| X/Y-Axis Output Noise | 190 nTrms |
| Z-Axis Gain Error | ±3% (25 °C, after API compensation) |
| Z-Axis Output Noise | 450 nTrms |
| Zero-Field Offset Drift | ±2 µT (-40 °C ~ +85 °C, after calibration) |
| Zero-g Offset | ±50 mg |
| Zero-Rate Offset | ±1 °/s |
No specification matches.
Last verification : 2026-11-02
Official documents and the technical data recorded for SEN0696. For a missing document or a specific revision, our experts send it to you.
DFRobot Gravity 10DOF IMU module combining accelerometer, gyroscope, magnetometer and barometer, with I2C or UART interface, for motion, heading and altitude change measurement.
| Parameter | Value |
|---|---|
| ADC Resolution | 16-bit |
| Angular Rate Ranges | ±125, ±250, ±500, ±1000, ±2000 °/s |
| Communication interface | I²C / UART |
| Connector Type | PH2.0-4P (Gravity pinout) / 2.54 mm pin header holes |
| Forced Mode Maximum Trigger Frequency | 200 Hz (avg=0 only) |
| Gravity | 10DOF IMU Sensor for Motion, Heading & Altitude Changes (I2C / UART, Plug & Play) |
| I²C Addresses | 0x4A (default), 0x4B, 0x4C, 0x4D |
| Magnetic Field Resolution | approx. 0.1 µT |
| Measurement Range | ±2000 µT |
| Measurement Ranges | ±2 g, ±4 g, ±8 g, ±16 g |
| Mounting hole diameter | 3 mm |
| Mounting Hole Spacing | 20 mm |
| Normal Mode Output Data Rate | 400/200/100/50/25/12.5/6.25/3.125/1.5625 Hz, typical deviation ±2% |
| Offset Temperature Error | ±200 nT/K |
| Operating Current | 3.59 mA |
| Operating Modes | Normal periodic measurement, triggered forced measurement, low-power sleep standby |
| Operating Voltage | DC 3.3–5 V |
| Output Data Rate (ODR) | High Performance / Normal mode: 12.5 Hz ~ 6400 Hz Low Power mode: 0.78125 Hz ~ 400 Hz |
| PCB Size | 32 mm × 27 mm |
| Pressure Long-Term Annual Drift | ±10 Pa |
| Pressure Measurement Range | 30 kPa ~ 125 kPa |
| Pressure Relative Accuracy | typical ±6 Pa within 700~1100 hPa, 15~55 °C |
| Pressure Resolution | approx. 0.0156 Pa |
| Pressure Temperature-Induced Offset | ±0.5 Pa/K |
| Programmable Interrupt Pins | ×4 |
| Sensitivity | ±2 g range: 16384 LSB/g ±4 g range: 8192 LSB/g ±8 g range: 4096 LSB/g ±16 g range: 2048 LSB/g |
| Sensitivity Error | ±0.5% |
| Sensitivity Temperature Drift | ±0.010 %/K |
| Temperature Absolute Accuracy | ±0.5 K within -5~55 °C and over full temperature range |
| Temperature measurement range | -40 °C ~ +85 °C |
| Temperature Resolution | approx. 0.000015 °C |
| X/Y-Axis Gain Error | ±1% (25 °C, after API compensation) |
| X/Y-Axis Output Noise | 190 nTrms |
| Z-Axis Gain Error | ±3% (25 °C, after API compensation) |
| Z-Axis Output Noise | 450 nTrms |
| Zero-Field Offset Drift | ±2 µT (-40 °C ~ +85 °C, after calibration) |
| Zero-g Offset | ±50 mg |
| Zero-Rate Offset | ±1 °/s |
Answers to the questions that the recorded characteristics of SEN0696 can answer. A question is not asked when nothing is recorded to answer it.
Yes — recorded under "Gravity": 10DOF IMU Sensor for Motion, Heading & Altitude Changes (I2C / UART, Plug & Play).
Similar parts to answer your needs. Compare the main characteristics. A recorded replacement is a documented relation; a similar product is a similarity only, never a compatibility claim.
10DOF IMU Sensor with Accelerometer, Gyroscope, Magnetometer and Barometer

Gravity: 6DOF IMU Sensor for Motion & Gesture Detection (I2C / UART, Plug & Play)

Gravity: 9DOF IMU Sensor for Motion, Heading & Orientation (I2C / UART, Plug & Play)

Gravity: 1602 LCD Keypad Shield For Arduino

Describe your application and constraints in a request.
What is recorded about the regulatory status and the life of this part.
No compliance statement is recorded for this part. Ask the supplier for the RoHS and REACH declarations and, for a radio product, the EU declaration of conformity.
| Current status | Status not stated |
| Key dates | Not recorded |
| Manufacturer part number | SEN0696 |
| Manufacturer | DFRobot |
DFRobot Gravity Sensor & Actuator System
Dual bipolar stepper motor shield for Arduino with DRV8825 driver · Ref. : DRI0023
Price on request
DFRobot Gravity Sensor & Actuator System
Analog Piezo Disk Vibration Sensor · Ref. : DFR0052
Price on request
DFRobot Gravity Sensor & Actuator System
2x2A dual-channel motor shield for Arduino
Price on request
DFRobot Gravity Sensor & Actuator System
Expansion board for Raspberry Pi Pico and Pico 2 · Ref. : DFR0848
Price on request
No advertising or analytics cookies. A single, strictly necessary cookie is set only if you sign in to your account. Your quote basket and comparison stay in your browser. Details